Easy beauty tips

Easy Beauty Tips

Everyone wants to look their best and as gorgeous as they can. Many of us spend a lot of money on branded beauty products and on many visits to the beauty parlor. There are a number of simple beauty treatments that we can use with things that are easily accessible in our homes. Here are a few home beauty tips that you can try using things from the kitchen without any extra cost.

  • To remove puffiness from the eyelids, manipulate a drop of very fresh castor oil on to them.
  • To cool your eyes, make eye pads using thick slices of cucumber. Another option is to use cotton pads soaked in cold milk. Lie down and place them on your clogged eyes and relax for a while.
  • Putting a drop of rose water into each eye just before you sleep can also refresh you eyes.
  • To prevent your lips from chapping, use hot water fermentation on your lips and then apply a mixture of vaseline and honey. Apply this combination about three times a week.
  • To prevent your lips from drying you can use a ground combination or rose petals and milk butter.
  • To delay age spots on your hand, use a piece of lemon and rub all above your hand, before washing. This will delay onset of age-spots.
  • If you have no time to shampoo your hair before going out, then brush 1 tablespoon of talcum powder or corn flour through your hair. Try this out first when you are not in hasten to make sure that it works the way you want.
  • To prevent hair loss you should have a biotin rich drink. Blend bananas with honey, yogurt and low fat milk drink this for some weeks.
  • While blow drying and setting your hair, blow-dry at hot on the roots of the hair roll your hair inwards or outwards at the ends. To improve the setting make sure the ends are evenly rolled in or rolled out. Heat the hair for a second and then let it cool. This process of setting the hair will last longer and make your hair look beautiful.
  • To condition your hair, after shampooing your hair take a few conditioners on your palm and rub it with both hands. Apply from the hair shaft moving downwards do not apply on your scalp. Rinse your hair after 5 minutes.
  • To add extra shine and glow to your hair add 2 tablespoons of malt vinegar use it as a last rinse and towel dry your hair.

Beauty Food

There is no doubt that all of us want to look gorgeous, slim and fit. One has to exercise sufficiently to look good. But it is significant to eat the right kind of diet to look beautiful.

Cause of Dark Circles

Our face attracts the most amount of notice. Therefore, we pay most attention to the way our face looks. We take special care of our face, its skin, its look and we try to present our face in the most beautiful manner we can.

Beauty Diet

Your diet contribute a great deal towards making you beautiful. Therefore eating a proper healthy diet is important to keep looking gorgeous.

Tips to Look Young

There will hardly be any one on this earth who wants to look old. In fact, almost every one of us wants to look young all through his/ her life. However, time is relentless and you tend to get older each year.

Hand modelling industry

Hand Modelling Industry

There are different types of modelling such as High fashion modeling, Glamour modeling, Petite modeling, Plus size modeling, Teen modeling, Mature modeling, Body Part Modeling (hand, foot, neck modeling, etc), Male modeling, Character or “Real People” modeling, Catalogue modeling, Showroom Modeling, Fit Modeling, Promotional (Trade Show) Modeling, and Editorial (Magazine and Newspaper) Modeling.
Among these different types of modeling, body part modeling is a special division. In body part modeling various parts of you body like your neck, feet, hand, leg, etc are used for modeling. The basic requirement to do hand modeling is that you should have a perfect body part. That means perfect nails on feet and hands, no scars or wrinkles, no veins should show up and the skin should be perfect.
In this article we are going to discuss about hand modeling and how you can become a good hand model.  In case of hand models the agencies look for models with long and slim fingers. The models in this division choose the same path of a regular model to find an agency and building a portfolio to project themselves through various mediums.
If you are aspiring to become a successful hand model, then here are some tips for you to get ready for the challenge. First of all have a look at you hands. Do you have long, straight and slim fingers with smooth and even cuticles? Are you nails beautifully shaped? Do you have a good and even skin tone? Is your skin free of scars and flaws? If your answer to all these questions is a ‘yes’, then you are eligible to become a hand model.
Well there is a lot of work to do to be in the eye of the modeling companies or clients. The first and foremost step is to take the images of your hands. You can take these images from your home too with the help of a friend. You can get the ideas to take the picture from the net. You have to take pictures of your hand in various angles in order to show variety. While taking these pictures you don’t have to worry much about the lighting and background.
After taking the images of you hand in various angles look for a good quality modeling agency near your town. Getting in touch with a good modeling agency can help you to project your self in the right manner. Some of the modeling agencies may not have a section for hand models but still you can give it to them. You may not know from where you will get a call.
If you are planning to take up hand modeling as a serious profession then its better to consult a good modeling agency. They can provide a professional outlook to your ambition. If an agency comes forward to sign you as a hand model be sure that they are a reputed agency in the field of modeling. Once you have reached the right agency you don’t have to look backwards.

The real thing

The Real Thing

Cecile and I have been friends since college,for more than thirty years. Although we have never lived closer than 100 miles to each other,since we first met,our friendship has remained constant. We have seen each other through marriage, birth,divorce,the death of loved ones — all those times when you really need a friend.

In celebration of our friendship and our fiftieth birthday, Cecile and I took our first road trip together. We drove from my home in Texas to California and back. What a wonderful time we had

The first day of our trip ended in Santa Fe,New Mexico. After the long drive,we were quite tried,so we decided to go to the restaurant near the hotel for dinner. We were seated in a rather quiet part of the dining room with only a few other patrons. We ordered Links Of London our food and settled back to recount our day. As we talked,I glanced at the other people in the room. I noticed an attractive elderly couple sitting a short distance away from us. The gentleman was rather tall and athletic looking, with silver hair and a tanned complexion. The lady seated beside him was petite, well-dressed and lovely. What caught my immediate attention was the look of adoration on the woman’s face. She sat,chin resting gently on her hands, and stared into the face of the man as he talked. She reminded me of a teenager in love!

I called Cecile’s attention to the couple. As we watched,he reached over to place a gentle kiss on her cheek. She smiled.

“Now that’s what I call real love!” I said with a sign. “I imagine they’ve been married for a long time. They look so in love!”

“Or maybe,”remarked Cecile,”they haven’t been together long. It could be they’ve just fallen in love. “

“Well whatever the case, it’s obvious they care a great deal for each other. They are in love. “
Cecile and I watched surreptitiously and unashamedly eavesdropped on their conversation. He was explaining to her about a new business investment he was considering and asking her opinion. She smiled and agreed with whatever he said. When the waitress came to take their order,he ordered for her, reminding her that the veal Links London was her favorite. He caressed her hand as he talked,and she listened raptly to his every word. We were enthralled by the poignant scene we were witnessing.

Then the scene changed. A perplexed look came over the finely wrinkled but beautiful face. She looked at the man and said in a sweet voice, “Do I know you? What it this place? Where are we?”
“Now, sweetheart, you know me. I’m Ralph, your husband. And we’re in Santa Fe. We are going to see our son in Missouri tomorrow. Don’t you remember?”

“Oh, I’m not sure. I seem to have forgotten,” she said quietly.

“That’s okay, sweetheart. You’ll be all right. Just eat your dinner, and we’ll go and get some rest. ” He reached over and caressed her cheek. “You sure do look pretty tonight. “

Tears coursed down our cheeks as Cecile and I looked at each other. “We were right,” she said quietly. “It is the real thing. That is love. “
Frankie Germany

Sharpening pastes

Sharpening Pastes

An Introduction to Sharpening-Pastes


Thiers issard “Bio-Diamond” Diamond Sharpening-Pastes and Chromox Finishing Paste

Ref. Bio-Diam 6 –Coarse-Grit 6 micron (Yellow colored)—for: heavy refining of edge direct from the hone; aggressive action or restoring.

Ref. Bio-Diam 3—Regular-Grit 3 micron (Green colored)—for: refining of edge direct from hone, intermediate action or restoring.

Ref. Bio-Diam 1—Fine-Grit 1 micron (Red colored)—for: regular use on razor’s edge.

Ref. Bio-Diam 0.25—Extra-fine-Grit 0.25 micron (Silver colored)—for: regular use and super-fine finishing on razor’s edge.

Ref. Chromox—Finishing-paste—green chromium oxide—recommended for use after diamond-paste stropping with grits finer than 0.50 microns.

Not All Pastes Are Created Equal

Like other aspects of straight-razor use, razor-sharpening has benefited from modern processes and materials. The use of today’s Diamond Sharpening-Pastes in your razor-sharpening regimen can vastly improve both the quality of your razor’s cutting edge and the comfort and closeness of the shave.

Razor-sharpening pastes have been around for years like wet shaving. The most common pastes used a fine powder of iron oxide, chromium oxide or graphite as the cutting agent, suspended in a carrier; this was spread onto a leather or wood surface, used as a strop to finish the edge. A bundle of strops would hang in a corner of the barbershop, each dedicated to a different type or coarseness of sharpening-paste.

The use of sharpening-pastes is similar to the use of hones: you begin with a coarser grit to accomplish the most work in the shortest time, moving on to progressively finer pastes to refine the edge, ending in a finely polished, mirror-like finish. Advances in metallurgy produced ever-harder steels, rendering ineffective the compounds used as cutting agents in the sharpening-pastes; they were actually softer than the blade they were expected to sharpen. Using such sharpening-paste made the blade duller, not sharper! All this changed with the development of diamond sharpening-pastes.

Diamonds are the hardest substance known to man; far harder than any steel yet developed. Industrial-grade diamonds, similar in hardness to gemstone-quality diamonds, are by-products of the diamond-mining industry. Their flaws, color inconsistencies, or other characteristics render them unsuitable for jewelry. Also, in the process of cutting and polishing gemstones, significant waste is produced. When all this is crushed to a fine powder the resulting particles acquire irregular cutting-edges. Being harder than any other substance, the particles hold those edges longer than any other material. This diamond powder does the actual work of sharpening.

However, all diamond compounds are not equal. The best are very carefully controlled in their manufacture, to assure consistency in the size of the actual particles. For example, a compound classified as “one micron,” though it may have particles smaller, should contain no diamond particles larger, than one micron. This is important, especially in a close-tolerance application such as producing a highly refined razor edge. All the diamond particles used in our “Bio-Diamond” sharpening-pastes are very carefully sorted to make sure that particles in each mix are exactly the given grade size.

Another differentiation between compounds is the carrier paste. In an industrial polishing application, an oil-based carrier, (typically a petrochemical) may be acceptable. In sharpening a straight razor, a water-based paste is preferable. This will easily rinse away after sharpening, lessening the risk of any skin irritation or infection. Our “Bio-Diamond” pastes are water-based, perfect for use in the sharpening of razors; they have no harmful chemical additives and are even “food-safe” if accidentally ingested.

Important: a razor edge can actually be too sharp, the result of over-sharpening with diamond-pastes. Such an edge will catch on every surface imperfection in the skin, causing irritation and razor-burn. For a close yet comfortable shave, the razor’s edge should glide over the skin, barely touching, catching only on the base of the hairs to be cut. Generally, using a diamond compound as fine as, or finer than, 0.5 micron can result in an over-sharpened edge. In most cases, one micron or smaller diamond sharpening-pastes are more than capable of sharpening a razor that has become dull through normal use. By starting with an even coarser grit—in the 6 micron to 1 micron range, depending on how dull the beginning edge is, you can refine the “not quite shave-ready” edge typically found on a new, out-of-the box razor.

Before sharpening a new razor, first try shaving with it. If it pulls, drags, or is in any way uncomfortable, sharpening is required. By this test, you learn how much sharpening to do. Generally, 20 round-trips on each side of the diamond-pasted strop will get it right. If, after sharpening and again trying to shave, it needs more work, repeat the process. You may have heard of many different ways to test the sharpness of a razor: the hanging-hair test, the standing-hair test, shaving your forearm, etc; but the only true test is actually shaving with it.

In most cases, a good paddle-strop or two (examples, our 4-sided paddle strop (ref. 444), or one or more 2-sided paddle strops (examples, ref. 259 or 276) and several different-grit diamond sharpening compounds (we recommend Bio-Diam 1, followed by Bio-Diam 0.25) will be all that are needed to maintain a fleet of daily shavers. What diamond paste will not do alone is establish a basic working edge on a razor that hasn’t seen a strop or hone in fifty years, or remove a ding or chip (the result of dropping the razor, or some other accident). For such repair, only a hone will do. But, once a hone has done the heavy work, diamond sharpening-pastes (this time, Bio-Diam 6 and 3,followed by Bio-Diam 1 and Bio-Diam 0.25) will refine the basic edge quicker and in much more controlled manner than a hone can.

Using the Bio-Diamond sharpening paste:

The best tool to use with your diamond sharpening-pastes, as we have said, is a paddle-strop. A surface of soft wood (such as balsa) can be chosen, but we prefer leather. In either case, the surface must be sufficiently rough or grainy to hold the paste. With too smooth or hard a surface, the paste will simply be wiped off with each pass of the blade; not only wasteful and expensive, but ineffective. The smoothest leather surface (of your paddle or hanging strop) should be reserved for either Chromox-paste application or use of an un-pasted strop in a final, pre-shave touch-up. The paste should be applied to the surface in very small amounts with our Bio-Diamond special push-drop dispenser applicator.

Dispenser procedure: Shake the dispenser gently to mix its contents. Remove the cap, then press the membrane at the base of the unit to eject drops of the compound (initially, you might have to press several times to get the flow moving). Ten to twelve drops will usually suffice for a first application. Any random compound emitted at start or end of the emission should be wiped away with the fingertips or a paper towel and deposited on the strop.

For a typical-sized paddle-strop, these 10-12 drops should be evenly spaced along the length of the strop. The dots should be thoroughly worked into the surface, using the fingertips or the heel of the hand. The more time spent on this step, the more effective the sharpening action will be. With successive use, as the surface becomes more built-up with abrasives, the effectiveness of the sharpening action will be improved. So, do not clean off the surface after use. When the effectiveness seems to have diminished, simply add a small amount of fresh paste (several dots will usually do), work it in, and continue.

As with all sharpening pastes, a surface coated with a given
grit of paste should be dedicated to that grit alone. While it is possible to increase the grit size, you cannot decrease it. A surface once used for .25 micron may subsequently be used with 1.0 micron, but you cannot do the reverse. Diamond-paste sharpening is similar to the use of other multi-paste systems and to the use of hones; that is, a coarser grade of paste is used for a dull blade, followed by finer and finer grades of paste until a properly refined edge is reached.

To maintain a fleet of regularly used razors, typically a two-step process, beginning with 1.0 micron, followed by .25 micron (and perhaps, to smooth the edge, a final application of Chromox paste) will achieve a perfectly smooth edge. To prevent cross-contamination, completely wipe off the blade when moving from coarser grit to finer, and again before moving on to your Chromox-pasted strop and/or further, to an un-pasted, finishing strop.

The motion used on the diamond-pasted surface is identical to that employed with any other pasted paddle-strop or hanging-strop: working from the blade’s heel to the point as you travel up or down the surface, leading with the razor’s back, and applying no pressure; using only the weight of the razor to maintain constant contact between the razor edge and the pasted surface. The typical “X pattern” used with traditional pastes and stropping is to be recommended. After having sharpened your razor, you should finish on the Chromox-pasted strop and/or an un-pasted leather strop. Your razor is now ready to use. Routine use of the un-pasted leather, pre-shave stropping may be resumed for successive daily shaves.

When needed (most probably every 2-3 weeks), the multi-step Bio-Diam strop procedure, should be all that is necessary to keep your razors in perfect shaving condition.

Using the Chromox finishing paste:

Chromium oxide edge-smoothing compound, when properly used on a paddle or hanging-strop, smoothes or takes the “bite” out of a very sharp, aggressive edge. Over-use will decrease the closeness of the shave; but proper use will give you the smoothest edge that you’ve ever experienced, with no loss of shave closeness. Our ref. Chromox paste is perfect for use after sharpening with extra-fine diamond grits 0.50 and 0.25 microns (and is also suitable for use after super-fine hones, such as Shapton 16,000 or 30,000 grits, Chinese 12,000 grits, or even Belgian Coticule stones). It is also sometimes of use after finishing with extremely fine non-diamond stropping-pastes.

It is recommended to use Chromox paste on either a fine leather paddle-strop (example, the finest side of our ref. 444 paddle-strop, or on the fine leather side of either our ref. 259, Voystrop-N or M, or 276 paddle-strops) or on a fine leather hanging-strop.

Important: the chromium oxide paste must fill the pores in your strop; you don’t want it to coat the surface. Before first use, with your fingers, rub in a generous amount of paste to completely cover the surface and fill all voids. Then, with a paper towel, wipe all the excess paste off the surface. When you are getting only a trace of lapping paste on your towel, your strop is ready for use. Before applying the chromium oxide paste, you should always stir it well, to avoid settling of the chromium oxide particles in the mixture. We recommend that you stir with a small piece of wood and then wipe this piece on the strop to be covered, so as to avoid wastage.

Some experimentation will be required to get the results you prefer. We suggest starting with ten back-and-forth passes in an “X” pattern on the strop as a first test, and then more if necessary. Remember, the only true test of the blade edge is shaving with it!

Suggested sharpening schedule:

For a blade needing restoration: Following use of an appropriate hone/or hones we recommend progressive use of Bio-Diam 6 micron, Bio-Diam 3 micron, Bio-Diam 1 micron, Bio-Diam 0.25 micron, Chromox and finally, an unpasted strop.

For an out-of-the-box razor, not yet shave-ready: We recommend progressive use of Bio-Diam 6 micron, Bio-Diam 3 micron, Bio-Diam 1 micron, Bio-Diam 0.25 micron, Chromox and finally, an unpasted strop.

For a razor already in regular use: We recommend, once every 2 or 3 weeks, progressive use of Bio-Diam 1 micron, Bio-Diam 0.25 micron, Chromox and finally, an unpasted strop.

Plus for daily upkeep of the same razor: We recommend pre-shave use of either a strop coated with Thiers-Issard non-diamond ref. 260 finishing-paste followed by an unpasted strop or, if desired, an unpasted strop alone.

by Thiers Issard